Downloads - Nuclear Measurements

Release Notes

WinSPEC is one of the basic programs to work with the MCA166 and the MCA527 Series.

This setup contains the both variants WinSPEC for Inspectors und WinSPEC for Automation.

Note: We have changed to the setup file format to *.msi. If a version of WinSPEC is on your computer, that has been installed with the previous setup file format, it is recommended to deinstall it before.

Release Notes

WinMCS is one of the basic programs to work with the MCA166 and the MCA527 Series.

This setup contains the both variants WinMCS for Inspectors und WinMCS for Automation.

Note: We have changed to the setup file format to *.msi. If a version of WinMCS is on your computer, that has been installed with the previous setup file format, it is recommended to deinstall it before.

Release Notes

WinSCAN measures max. 2000 single MCA spectra and assembles a MCS spectrum from it. The measurement is saved in one *.spe file.

Release Notes

Program for U235 enrichment measurements with NaI-detectors.

Release Notes

WinUF6 allows enrichment measurements on UF6 - cylinders with HPGe-Detectors.

Release Notes

WinTimestamps allows to use the MCA-527 as timestamps recorder (list mode).

The program allows to use the MCA-527 as an transient recorder independently from other applications.

Important hints

The program allows to use the MCA-527 as an oscilloscope independently from other applications.

Release Notes for the licensed program

Datasheet

Hints for Windows 7

Program for nuclide identification from gamma spectra. Identify is also as OEM version available. Please do not hesitate to contact us if you have any further questions..

MCA Wand is a file converter, which supports different file types (from spe, chn, spc to spe, chn, dat).

Features:

• Multi File Converting
• Preview of spectra files

Program for the calculation of the transmission of x-rays and gamma-rays.

The program allows to set a fixed IP address on MCA-527.

Release Notes

The MCA-527 RS485 Configurator allows to configure the RS485 interface of the MCA-527 for the intended operating conditions.

The MCA-527 Basic State Configurator is intended for detector manufacturers who integrate the MCA-527 Micro, Nano or OEM within the detector encasement or for technicians who construct systems with permanently connected detector.
The tool allows to predefine the basic state of the MCA-527 (firmware version 21.00 or higher). The basic state is stored in the EEPROM and is established during power-up or during reset.

Before using this tool, the most suitable parameters for the detector have to be determined with any qualified program (e.g. WinSPEC). After that the parameters can be taken over by this tool.

The "MCA-527 Detector Information Writer" is intended for detector manufacturers who build detector modules for the Cube527.

If you are also interested, please ask for the necessary technical requirements.

The MCA-527 Power Module Reconfigurator allows to reconfigurate the maximum adjustable high voltage  of the MCA-527 power module (full und lite version) to 5000V.

By default, the high voltage is limited to 3600V. Users who want to use a 5000V high voltage module have to increase the maximum adjustable high voltage with this program.

The device driver is needed for MCA-166 USB, MCA-527 and NScan. If you want to run the devices with self-developed applications, you have to install the device driver with this installation program. The installation programs for applications developed by us already include the installation of the device driver.

Run the installation program before you plug in the device.

The device driver is needed for MCA-166 USB, MCA-527 and NScan. If you want to run the devices with self-developed applications, you have to install the device driver with this installation program. The installation programs for applications developed by us already include the installation of the device driver.

Run the installation program before you plug in the device.

You can find the firmware for newer hardware versions on this website. If you have an MCA527 with an older hardware version, please contact us personally.

The GBS Firmware Loader allows uploading the following firmware to the corresponding unit type.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

*The hardware version is displayed in the "Diagnostics" dialog of the programs for the MCA.

The MCA communication library provides functions that can be used by MCA-166 or MCA-527 users for developing their own MS Windows applications. The functions are described in the User's Manuals for the MCA-166 and MCA-527.

This package provides the C++ source code of an MCA communication library with essential basic functions similar to the Windows communication DLL. Further it contains a simple command line tool to communicate with an MCA. The software uses the FTD2XX library which is based on an unmodified version of libusb. It is intended for Linux systems. Documentation is included.

This example code can be used for developing an own application that needs to read list mode 4 data from a *.mca file.

Description of the MCA527 firmware commands (2024-07-04)

Description of the MCA Communication DLL (2024-07-04)

Description of the MCA communication library which is available as source code for Linux systems (2022-05-10)

MCA Spectral Data Format (2018-09-21)

MCA Binary Data Format (2021-09-20)

Description of the MCA527 serial Interface, especially within bussystems

Use of the MCA User Data Memory by Specific Applications (2012-10-30)

Quick IDENTIFY is a function library that third-party providers can integrate into their software.

GBS_MCA_Cmd is a simple command line tool to communicate with an MCA-527 or MCA-166 under Linux systems. User information (2022-05-10)

How to do a optimum setup fo MCA527

How to do a MCA527 Setup (Short Version)

Description of the MCA527 Oscilloscope Mode (2013-09-12)

Explanations of the list modes